Telephone: +44 (0) 20 8281 6370
Home | CORR-EX News | SuperCORR A Protects Electrical Control Systems In Waste Water Treatment Plants

SuperCORR A

SuperCORR A protects electrical control systems against corrosive environments in Waste Water Treatment Plants

 

 

SuperCORR A


Super
CORR
A protects electrical control systems against corrosive environments in Waste Water Treatment Plants

 

 

Waste water treatment plants are subject to corrosion and rust from a variety of causes. One which is Hydrogen Sulphide gas, (H2S.). Corrosion is an insidious and costly problem that causes just about every metal and metal alloy to fail over time. Metals in electrical and electronic control systems, components, connectors, and switches are of most concern.

Corrosion is found in almost all process industries including wastewater treatment plants, pulp and paper mills, fertilizer plants, and numerous other industries and is not going away.  Establishing a Preventative Maintenance Program that includes corrosion prevention makes it a problem that can be cost effectively dealt with.

Corrosion prevention

One proven and positive way to reduce, if not prevent, corrosion altogether from causing electrical, electronic systems and component failures is by using an ultra-thin film water displacing lubricant material with corrosion inhibiting compound.

SuperCORR A has all these properties.  A proprietary formulation packaged in aerosol cans it uses a non-flammable fast drying carrier solvent. The aerosol is supplied with a flexible tube applicator which allows the protective coating to be applied accurately even in difficult to get to components.

Removal of surface contamination from the metallic contact surfaces on switches and circuit breakers is essential to ensure fault free operation.

The aerosol uses the unique SuperCORR A formulation to lift and remove dust and soils from the metal contact surfaces. An inert compound that neither reduces nor increases the electrical conductivity SuperCORR-A also provides long term protection from corrosion and electrical arcing that can lead to shorts and subsequent circuit failures.

An application of SuperCORR A also prevents corrosion on metals and components in areas where acid or corrosive vapours may form or  accumulate such as battery storage compartments and external power connectors.

Testing SuperCORR A in corrosive environments

SuperCORR A (MIL L 871777A Type 1 Grade B lubricant) was subjected to extensive and vigorous Mixed Flowing Gas (MFG) testing at Battelle Laboratories under a U.S. Government contract.

Specifications ASTM B827 and  ASTM B845 Class III MFG testing protocol were used. This included gases with high corrosion potentials including Hydrogen Sulphide (H2S), Nitrous Oxide(NO2), and Chlorine (Cl2).

ASTM B845 refers to techniques for mixed flowing gas (MFG) tests containing gases that are applied to evaluate devices containing electrical contacts such as slip rings, separable connectors, electromechanical relays or switch contacts.

The MFG tests accelerate corrosive degradation processes. Connectors and contacts within closed electronic cabinets may be affected by an environment of different severity than the outside of these cabinets.

ASTM B827 outlines procedures for conducting environmental tests involving exposures to controlled quantities of corrosive gas mixtures. Equipment and methods for gas, temperature, and humidity control for tests to be conducted in a reproducible manner are described.

Reproducibility is measured using control coupons whose corrosion films are evaluated by mass gain, coulometry, or by various electron and X-ray beam analysis techniques.

Reproducibility can also be measured by in situ corrosion rate monitors using electrical resistance or mass/frequency change methods. Full copies of these tests can be made available on request.

Industrial applications of SuperCORR A 

SuperCORR A has a proven performance record in protecting electrical components, systems, connectors and electronics. The coating will also prevent the ingress of moisture and other contaminants onto the connector surfaces.  These initiate corrosions and cause intermittent component failure or a premature degradation of component performance.

The Battelle Laboratories studies provided data and related processing information validating the benefits of using SuperCORR A. to protect the electrical connectors of line replacement units (LRUs) used in military aircraft avionic applications.

The results of the laboratory and field-testing activities conducted in these studies confirm that SuperCORR A is an extremely effective coating to protect electronics, electrical components and systems including switches and connectors with no compromise of the integrity of the electrical component/system even in very corrosive environments.

As a result of testing on site at a number of private and public companies with the confirmatory work at  Battelle Laboratories SuperCORR A is being used to reduce maintenance and repair costs in a range of different industrial applications. Wastewater treatment plants, pulp and paper mills, automotive and heavy equipment industries and in the power production sector oil and gas and renewable energy and in both the aviation and maritime industries.

For more information visit:

https://www.corrosion-protect.com/corrosion-protection-products/supercorra-corrosion-prevention/

Further information

We can provide you with a Material Safety Data Sheet, independent laboratory reports, product samples or technical assistance. For more information or advice please contact us by telephone on +44 (0) 20 8281 6370 or use our contact form.

All products are supplied and supported by EnviroTech Europe Ltd.  Manufactured in the United Kingdom and available on short delivery times through our dedicated team of distributors in Europe and the Middle East.

Share this page:

Related Posts