Telephone: +44 (0) 20 8281 6370

Telephone: +44 (0) 20 8281 6370

Clarea HC 40
ProSolv5408e

HC 40

Non chlorinated surface cleaning agents for safe removal of dirt, oil, grease and other contaminants.
Flash Point over 40°C.

Clarea Solvent Cleaners | Clarea HC40 Solvent Cleaner

Non chlorinated surface cleaning agents for safe removal of dirt, oil, grease and other contaminants

DESCRIPTION
Clarea® HC40 is an aliphatic hydrocarbon based low odour degreasing solvent with a flash point of 40°C. It will remove oils, greases, hydraulic fluids cutting fluids and a wide variety of hydrocarbon based protective coatings. It can be used as dip, brush or in hand-wipe process. It has a relatively fast evaporation rate and is most suited to hand wipe and small immersion tanks.

MATERIALS COMPATIBILITY
Clarea® HC40 is compatible with all metals and many plastics and other composite materials.

PROCESSING
• To reduce solvent losses keep containers closed.
• Dip tanks should have a suitable close fitting lid which should be closed when not in operation.
• Stubborn soils can be worked with a brush.
• Excess solvent can be removed with cloth.
• Allow components to air dry in ventilated area.
• Blowing air over the components will aid drying.

Suitable equipment which can be used with Clarea® HC40 is shown here.
Technical data sheets can be downloaded in PDF format here.

HEALTH & SAFETY
Clarea® HC40 is a non-carcinogenic solvent mixture that is safe to use in many applications and is a not classified as flammable. EnviroTech recommends that safe work practices are implemented whenever handling chemicals of any kind to minimise exposure levels and prevent toxic effects.

Please refer to the Clarea® HC40 Material Safety Data Sheet available on request at here for more specific information on workplace exposure levels, toxicity and personal safety recommendations.

REGULATORY INFORMATION
Clarea® HC40 is classified as flammable and has been shown to neither deplete the ozone layer nor contribute significantly to global warming

Solvent Properties

Typical Physical Properties

Boiling Point (°C ) minimum162°C
Boiling Point (°C ) maximum181°C
Specific Gravity @ 15°C (H20=1)0.77
Colour Saybolt ASTM D156+30
Aromatics mg/kg<100
Benzene mg/kg<3
Flash Point TCC (°C) minimum40°C
Auto ignition temperature270°C
Flammability Limits (vol. %)0.6 – 6.0 %
Vapour Pressure @ 20°C (mm Hg)<3
Vapour DensityHeavier than air
Evaporation Rate (Butyl Acetate = 1)0.23
Specific Heat @ 25°C (KJ/kg/°C)2.0
AppearanceClear & free of suspended matter

Cleaning, Corrosivity, Residue

Kauri Butanol Number32
Copper corrosion (3hr @ 100°C) ASTM D1301
Doctor test ASTM D235Negative
Non-Volatile Residue (ppm)10

The above represents typical properties of Clarea® HC40 degreasing and cleaning solvent, but do not represent any other product specification.

Other Clarea® HC40 products have similar characteristics, but are not necessarily identical to the properties listed above. For specific values and specifications, consult the product’s Certificate of Analysis.

Packaging

Clarea® HC40 is available in the following container sizes:
205 lt drum
25 lt can
5 lt can

We can provide you with a Material Safety Data Sheets, independent laboratory reports, product samples and technical assistance.

For more information or advice please telephone us on +44 (0) 20 8281 6370 or use our contact form.

All products are supplied and supported by EnviroTech Europe Ltd.  Manufactured in the United Kingdom and available on short delivery times through our dedicated team of qualified distributors in Europe and the Middle East.

Share this page: